Model 3193 is the multifunctional gauge of power. Instrument can work with the wide range of lines of force, beginning from the single-phase lines and concluding by 3- phase, 4- wire networks. So it makes it possible to measure to 6 single-phase systems and to ensure the effective measurement of power. Furthermore, it ensures the analysis of harmonic components and the measurement of vibrations (with the use of the corresponding option).
Into standard delivery set enter the interface GP-IB/RS-232C and disk drive down 3.5 inches, which ensures the transmission of data for processing and analysis down the computer. This instrument is ideal for those, coma is required large effectiveness before the measurements.

Specification

Measured lines	Single-phase 2- wire, single-phase 3- wire, three-phase 3- wire, three-phase 4- wire, (it depends on the utilized options).
Measured values	With use as far as one of the options 9600, 9601, 9602: Stress, current, the peak value of relationship stress/current. Effective, reactive, total power, capacity rate, phase, frequency. Integrated value of current, power, nominal load, efficiency. With the use of option 9603: Stress, the torque, the RPM- number of revolutions per minute, frequency, the power of engine. With the use of option 9605: Harmonics, the waveform, fluctuation of stress, the function of the measurement of twinkling.
Intervals of the measurements	Stress: from 6.0000 [v] to 1.0000 kV (it depends on options) Current: from 200.00 [m]A to 500.00 A (it depends on options) Power: It depends on the combination of the range of stress and current.
Range of the integration	From 0 to ±999999 Of [tA]h/TWh, (time of integration to 10000 hours).
Accuracy	With use as far as one of the option 9600, 9601, 9602: ± 0.1% of measuring. value ± 0.1% of entire scale (stress, current, power, with the frequency from 45 [d]o 66 Hz).
Frequency	With option 9600: DC, 0.5 Hz to 1 M[Gts]. With the option the 9601:5 Hz of [d]o 100 kHz. With option 9602: DC, 0.5 Hz of [d]o 200 kHz (it depends o[t] of the accuracy of tongs).
Output signal	Analog level: Stress, current, active power, 5 [v] DC of the entire scale. Monitor of the timetable of the signal: Stress, current, 1 [v] of rms of the entire scale. D/The output: Are derived 8 arbitrarily selected parameters, ±5 in DC of the entire scale.
Other functions	6.4 inches TFT liquid-crystal display, RMS/MEAN rectification, FDD, GP-IB/RS-232C interface, scaling, averaging.
Power source	100/120/200/230 [v], AC (it is switched automatically), 50/60 Hz.
Sizes and the mass	150 mm altitudes × of 430 mm latitude × 370 mm of thicknesses. Mass: 15 kg.
Accessories	Power cord, cord for the stress, connector.

Information for the order
Measurements cannot be conducted by means of only GAUGE OF POWER 3193, it is necessary to acquire the firm optional input module (it is possible to select as far as 9600, 9601, 9602).

Observations on the selection of the input module

• Use for each measuring line one and the same input module
• You will establish modules before the sequence, beginning based on channel 1
• For models 9603 or 9603-01 it is possible to establish only one module.
• When model 9602 is selected, use optional sensor with the [tokopreobrazuyushchimi] tongs.

The options, which can be established at the plant (you will determine with the order):
9600 AC/DC THE MODULUS OF THE DIRECT INTRODUCTION
9601 AC THE MODULUS OF THE DIRECT INTRODUCTION
9602 AC/DC INPUT MODULE WITH THE [TOKOPREOBRAZUYUSHCHIMI] TONGS
9603 MODULI OF INPUT OF EXTERNAL SIGNAL (only 3193)
9604 MODULES OF THE PRINTER
9605 MODULE OF THE MEASUREMENT OF THE HARMONICS/OF TWINKLING (only 3193)

Options:
* 9270 SENSORS with THE [TOKOPREOBRAZUYUSHCHIMI] TONGS (20[A] ACE)
* 9290-10 ADAPTER with THE [TOKOPREOBRAZUYUSHCHIMI] TONGS (1500[A] ACE)
9232 PAPERS FOR THE PRESS (10 m, 1 cylinder, for 9604)

* marking [SE] is absent