Instrument makes it possible to analyze all parameters of electric power according to ALL-UNION STATE STAN. 13109-97 with the high accuracy and the wide range of the measured values:
- The variation of the stress
- The fluctuation of the stress
- The dose of the flicker: short-term, prolonged
- The nonsinusoidality: curve of stress, harmonic components of the three-phase networks
- The frequency deviation
- The pulse overvoltage
- The duration of dip
- The asymmetry of the voltage of the three-phase networks
- The coefficient of the temporary overvoltage

Instrument includes the functions:

1. Analyzer of the quality of the electric power
2. Oscillograph
3. Multimeter
4. Registrar

• The presence of the function Of true RMS makes it possible to conduct the measurements of the full values of voltage and current with the high accuracy.
• Measurement of the harmonics of current and voltage to 50, the parameters OF BONDS.
• Image of waveform both before the digital and before the graphic form
• 4 channels for measuring of current and 4 channels for measuring the stress
• It works with single-phase networks 2 and 3 wire diagrams, by three-phase networks 3 and 4 wire diagrams.
• Measurement of current with the use of any of five types of current-measuring tongs - 5/100/500/1000/5000 A
• Simultaneous measurement and retention of results makes it possible not to lose valuable information, especially about the failure. Ranges of record from 1 s. to 2 hours (time interval between two sequential [vyborkami])
• Colored [ZHKD] 6,4”, 640*480 of the pixels
• Compact and light instrument: with size the sheet of the paper of the size Of [a]4 and with the weight of 2,25 kgf
• Possibility of conducting the continuous measurements in the course of one month
• Large storage capacity for record and storing the data: internal storage to 13 mb., the additional maps of memory to 512 mb.
• Built-in disk drive for PCMCIA of maps (map of memory)
• Built-in interfaces RS232 LAN- port for the work through the Internet, the connection for the sake of PK and the printout of the results
• Channels of the entrance/of output for the warning system
• Input resistance: on the stress: 4 [M]W ±10%, on the current: 200 [k]W ± 10%
• Conclusion of measured data before the real time: the waveform, vectors, measured values and harmonics.
• Maximum stress: 780 [v] ACE, 1103 [v] peak, the current of 1,7[V] ACE, 2,4 [v] the peak

Specification

Instrument conducts measurement and analysis not only of the parameters of the indicated beside ALL-UNION STATE STAN. 13109-97, but also following values

Stress RMS	To 600 [v], the accuracy is THE ACE: ± 0,2% OF IV + 0,1% OF [VPI], DC: ± 0,3 % ИВ+0,4 % ВПИ
Current RMS	To 5000 A, depending on tongs, the accuracy: ± 0,2% of IV + 0,1% OF [VPI] + the accuracy of the tongs
Overvoltage (pulses)	2 MHz frequency, 2000 [v] peak, the conclusion of signal 4 ms., min. the determined duration of 5 m[sek]., the accuracy: ± 5,0% OF IV ± 20 [V]
Frequency	42,500 - 69,000 Hz, the accuracy: ±10 MHz (10-100% of range)
Voltage surges	Amplitude and duration of jump is measured. Accuracy is the same as in stress RMS
Dips	Amplitude and duration of failure is measured. Accuracy is the same as in stress RMS
Active power	Is calculated continuously every 10-12 cycles, accuracy ± 0,2% OF [IV]+ 0,1% OF [VPI]+ the accuracy of the tongs
The reactive power	Accuracy: ± 1[ed]. mf. from the calculation of each measured value
Capacity rate	Range from 1,000 - 0,000 and to + 1,000; the accuracy ± of 1 un. of mf.
Shift coeff. of the power	It is calculated as a phase difference of the fundamental harmonics of voltage and current. Range: From -1,000 to 0,000 and to +1,000; the accuracy ± of 1 un. of mf.
Coeff. imbalance. the stress	It is calculated for 3 phase networks of 3 wire and 4 wire diagrams
Coeff. imbalance. the current	It is calculated for 3 phase networks of 3 wire and 4 wire diagrams
Twinkling DV10	Short period of the twinkling Of pst, the long period of the twinkling Of plt. DV10, DU, accuracy ±2%[IV]
Twinkling IEC	Standard IEC61000-4-15. the accuracy ± 5% of IV
Harmonics	Stresses, current, the power: with the 1-[oy] to the 50-[oy]
	Accuracy	Stress, the current: 1-20: ± 0,5% OF IV + 0,2% OF [VPI]; 21-50: ± 1,0% OF [IV]+ 0,3% OF [VPI] the power: 1-20: ± 0,5% OF IV + 0,2% OF [VPI]; 21-30: ± 1,0% OF IV + 0,3% OF [VPI]; 31-40: ± 2% OF IV + 0,3% OF [VPI]; 41-50: ± 3% of IV

Options

General given
Max. stress 780 [v] ACE, 1103 [v] peak, the current of 1,7[V] ACE, 2,4 [v] the peak
The operating temperature of 0… 40 °[S], humidity not are more than 80%
Overall sizes/mass Of [a]4/of 2,25 kgf

It enters into delivery set
3196 - analyzer, wire with the clamps for measuring the stress 3 m, the unit of storage batteries, net of [adapter]/[ZU], LAN joint, the management of the user